Minka-group F521-WHF User Manual

INSTRUCTION MANUAL WARRANTY CERTIFICATEALUMABY

4 Step 1. (Fig. 5) Remove the upper cover by remove the 4 screws from the motor.Step 2. (Fig. 6) Insert the blade through the access window from

5WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the proper insta

Fig. 12DOWNRODCANOPYCANOPY COVERSET SCREWSTHREADED PINOUTLET BOXHANGER BRACKETDOWNRODSUPPLYWIRESFig. 8Fig. 10 Fig. 11Fig. 9Fig. 13REGISTRATIONSLOTCROS

6ELECTRICAL CONNECTIONSFollow the steps below to connect the fan to your house supply wires. Use the wire nuts supplied with your fan. Secure the wire

Fig. 14 Fig. 15SWITCHOUTLET BOXWALL PLATESCREWSSCREWSSUPPLY CIRCUITBLACK/WHITEBLACK/WHITEBLACKBLACKBLACKBLUEBLUEBLUEBLUEBLACKGROUND CONDUCTOROUTLET BO

7Remember to shut the power off at the circuit breaker or fuse box.WARNING: HOOK UP IN "SERIES ONLY" DO NOT CONNECT THE HOT AND NEUTRAL WIRE

8FINISHING THE INSTALLATION Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw

Fig. 18INSTALLING THE LIGHT KIT MOUNTING PLATEStep 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove)Step 2

10Fig 19INSTALLING THE LIGHT PLATE NOTE: Before starting installation, make sure power is turned off at the circuit breaker.1. Remove 1 of 3

11WARNING: Shut of the power supply before removing or replacing lamp. In handling of halogen bulb, care should be taken not to touch it with your bar

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.

Fig 20MOUNTING PLATEBULBGLASS SHADEFig 21MOUNTING PLATEALUMINUM COVER

12Restore power to ceiling fan and test for proper operation.1. The fan 4-speed control is used to set the fan speed as follows:0= Turns the fan off1=

Warm weather - (Forward)A downward airflow creates a cooling effect as shown in Fig. 23. This allows you to set your air conditioner on a warmer setti

13Here are some suggestions to help maintain your fan.1. Because of the fan's natural movement some connections may become loose. Check the suppo

14TROUBLESHOOTINGSYMPTOM Fan Sounds Noisy SOLUTIONAllow a 24-hour "break-in" period. Most noises as sociated with a new fan go away during

SYMPTOM Fan Wobble SOLUTIONNOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even thou

1552"SPECIFICATIONSThese are typical readings. Your actual fan may vary. They do not include amps and wattage used by the light(s).For any additi

The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only vali

Date Purchased Store Purchased Model Number S

CONTENTSSAFETY RULES... PACKAGE CONTENTS...

SAFETY RULES1 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all inst

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.

212b. Wall plate w/2 mounting screws13. Balancing kitA. Mounting hardware: #10 x 1.5 Wood screws (2 PCs.) #8 x 3/4" Machine scre

3Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. INSTALLING THE FANMOUNTING OPTIONSIf there i